The Tesla has an OLED screen, and features great, well placed buttons.
It is built well, works well and is definitely worth owning!
The Tesla is the same length as the VAMO in full size.
It has an ergonomically slotted tube.
You can use most eGo -510 style clearomisers/ atomisers/ cartomisers, etc…
This APV fits perfectly in the hand, is light weight, and very easy to operate.
This would easily fit into any seasoned vaper’s collection or even make a great beginner starter kit, for a diligent first timer.
What do you get in this Tesla Variable Voltage/Wattage APV Kit:
1x Tesla body
2x 18650 rechargeable batteries
1x Dual Coil Tank with Cartomiser
1X spare Cartomiser for the DCT
1x User guide
TESLA Variable voltage / wattage functions and features:
1. Constant voltage and Constant wattage(dual mode output). In constant voltage mode, the output voltage can be adjusted between 3.0V - 6.0V in increments of 0.1V. In constant wattage mode, the output power can be adjusted between 3.0W and 15.W in 0.5W increments.
2. Single cell 3.7V battery input operational voltage is 3.2V - 5.0V
3. Button adjustments allows you to choose between 25 possible wattage settings, and 31 possible voltage settings.
4. Atomiser resistances check function, which can test and display the resistance of the atomiser in Ω.
5. OLED display, which can show the battery input and output voltage, atomiser resistance, output power, or short-circuit warnings.
6. Short circuit protection, and reverse battery installation protection. If the battery is installed backwards, the control panel will switch to protected mode, so that is doesn’t damage the internal components of the Tesla.
7. Low voltage warning, will stop use of under-charged batteries and display the “Low V” warning.
8. Short circuit and unsafe amperage protections. the Tesla should detect external short circuits and disengage to protect the user.
The Tesla will also detect if the attached atomizer resistance is too low to safely draw current. In both cases the Tesla will disengage output automatically
Upon the Tesla’s system start up, the Screen will boot up with the word Tesla, if the battery is low the display will boot with the words “Low V” .
During the boot sequence of this device, do not attempt to operate any functions, but allow the device to boot into standby please.
When the system boots into standby, use the fast click (5 click on/ off function) to turn the device on. The word Tesla will display on the screen.
If the battery voltage is sufficient for operation, the system will turn on and display the message “System on.”
Upon first turning the system on, the output will be in a “locked” state, press both the - and + buttons at the same time to switch the unit into an unlocked state, and you will be able to adjust operations.
The large button is your activation button.
To toggle the device between on or off, you need to fast-click the activation button 5 times (button presses must be very fast, within two seconds.)
When the unit is off, there will be no output from the Tesla, and the OLED will not display.
When on, the Tesla will be ready to use.
The - (minus) button is the voltage and wattage reduction button. Pressing - , will adjust the current value of either voltage or wattage down, and the corresponding voltage, or wattage numbers will be displayed on the OLED screen.
When the unit is adjusted below 3.0V, or 3.0W, it will cycle back to the highest setting (6.0V or 15W.)
The + (plus) button is the voltage and wattage increase button. Pressing + will adjust the current value of either voltage or wattage up, and the corresponding voltage or wattage numbers will be displayed on the OLED screen.
When the unit is adjusted above6.0V, or 15W, it will cycle back to the lowest setting (3.0V, or 3.0W.)
To check the Battery voltage, hold the - button down for two full seconds while the OLED screen is on and unlocked.
The Screen will then display the battery’s current operational voltage.
To check the atomizer resistance, hold the + button down for about two seconds while the OLED screen is on and unlocked.
The screen will then display the connected atomizer’s resistance.
To toggle the device between locked and unlocked output states,press both the – and + at the same time.
To access the Tesla menu, hold the + button for about eight seconds.
The menu interface will allow you to adjust 3 Tesla settings.
1: When the interface displays “Power Voltage”, you can use this menu option to change between‘Constant wattage’ and ‘Constant Voltage’ mode for the device.
Pressing the - button will switch between the two menu options.
2: When the OLED interface shows the word “Power” the device will be set into constant wattage mode, and regulate itself via calculated wattage output.
When the interface shows the word “Voltage” the unit will be set in constant voltage mode, and will regulate itself via output voltage.
3: When the Tesla interface displays the words “LCD Display”, you can use this menu setting to adjust the content displayed on the OLED screen during use. Pressing the - button will switch between menu options.
4: The menu setting “Voltage”, will display the output voltage or wattage of the Tesla on the screen while in use.
5: The menu setting “Resistance”, will display the Ω resistance of the atomizer during use.
6: The setting “Battery”, will display the current output voltage of the battery you are using on the OLED screen during use.
7: The final menu option“ON/OFF” will toggle the OLED display on the Tesla to either active or inactive during the use of the device.
As with other menu options, you can use the –button, to toggle between settings
In the menu mode, the + button is used for cycling menu categories, and the - button is used to confirm the setting. Using these two buttons, you will be able to navigate the Tesla menu. The menu navigation will exit after no buttons have been pressed for about three seconds.
8: When the system powers down via the fast click (5 click) function, the OLED will display the word Tesla and upon successful shut down will display the words “system off”, which indicates a successful shut down.
9: When an atomizer is attached with a resistance lower than 1.2 Ohms, the Tesla display will show“Low Resistance”, and cease function until an appropriately built atomiser is connected.
10: When an output short circuit is detected the screen will display the words “Short”
11: When the battery voltage is below 3.2V, the unit will display “Low V” on the screen, when you attempt to activate it. The unit will resume normal function when appropriately charged batteries are installed.
SLB eGo-V v3 MEGA battery 1300mah PassThrough variable voltage 3-6V and variable wattage 3-15W
Specifications Variable voltage battery from Sailebao :
This is the newest battery released on market from Sailebao . The main extra feature , is the variable wattage , which was missing on the previous models ( slb ego-v2 and ego-v batteries ) .
The package contains the following :
1 X SLB eGo-V v3 MEGA battery 1300mah PassThrough variable voltage 3-6V and varia...
SLB eGo-V v2 MEGA battery 1200mah PassThrough variable voltage 3-6V
Specifications Variable voltage battery from Sailebao :
The SLB eGo-V v2 MEGA battery 1200mah PassThrough variable voltage 3-6V is the newest battery made by Sailebao . It has variable voltage from 3v to 6v with 0.1V . Unlike other batteries in its class with variable voltage, the battery eGo-V has a USB connection on the bottom, so you can use and upload the same time. EGo-V battery contains lithium p...
UD AGA-TD rebuildable dual coil atomizer with pyrex tank
The AGA-TD RBA atomizer is a genesis style atomizer made entirely of 304 grade stainless steel ( including center pole ) and with a tank made of pyrex glass. It has two large air holes located on the top cap. Its designed with two negative and one positive post for dual coil builds.
The package includes the following :
1 x UD AGA-TD rebuildable dual coil atomizer with pyrex tank
1 x Resistance wire
1 x Mesh
Rebuildable AGA-T+(V2) tank , genesis style atomizer .
This is the upgraded version of AGA-T atomizer . It is made from 304 grade stainless steel and the tank is made of polycarbonate( or glass if you want ) , having a capacity of 3.2 ml .
It is used with stainless steel mesh for wicks .
It has a press on cap system for the adjustement of the airhole .
This is an advanced user piece , especially for moders .
It will require a certain level of mechanical skills and knowledg...
Variable voltage eGo/510 USB Passthrough
The Variable voltage USB passthrough for the eGo / 510 electronic cigarette featuring 4 different voltage settings.
This variable voltage USB passthrough is compatible with most EgO/EgO-T/ EgO-C atomizers, clearomizers and cartomizers. It is also compatible with most 510 threaded atomizers, cartomizers, clearomizers and tank systems.
The Variable voltage passthrough features four user selectable volta...
Vapo V5 Stainless steel electronic cigarette MOD .
This mod is compatible only with 14500 batteries .
The package includes the following :
Body Vapo V5 stainless steel (without battery)
Technical specifications :
Color: Stainless Steel
Thread : eGo/510
Working Voltage: 3.7V
Compatible batteries : 14500 batteries
Length : 102mm
Diameter : 17mm
You can use this battery fo...
Odysseus Stainless Steel Rebuildable Tank Atomizer ( Clone )
This is the first repairable multiatomizer in the e-cigarette's world, with his own liquid tank and with liquid control in order to avoid overflow or overcharging the resistance.
The Odysseus SS atomizer is using silica and kanthal for wick and resistance .
In order to control the flow of e-liquid to the resistance you need to rotate the central mouthpiece .
VV-PCCP Kit is a great kit for vapers . It is a incredible Variable voltage device with multi functions . Beside you can charge your electronic cigarette , you can charge other electronic devices . If you have this you don't need anymore a battery because you can connect the atomizer to the PCCP Power bank and you can vape a long time because it has a capacity of 6600mAh .
This kit contains the following :
1 x Adapter with LCD Screen
1 x USB mini c...
Smoktech Zmax variable voltage / wattage e cigarette ( VV & VW MOD )
The new ZMAX Advanced Personal Vaporizer is sleek, powerful, reliable, full featured and very well built just like its cousin the VMAX. With this new version, Voltage or Wattage is variable 3-6 volts or 3-15 watts respectively, using a single 18650 IMR battery . Check atomizer/carto resistance and battery voltage too!
Short description of Zmax variable voltage / wattage e cigarette ( VV &a...
Smoktech Octopus RDA rebuildable dripping atomizer
The Smoktech Octopus RDA (Rebuildable Dripping Atomiser) is a great new way of flexible rebuildable dripping!
This atomizer has a coil attached to wicks allowing for more e-liquid to be added to it at one time. The wicks do an excellent job providing e-liquid to the coil and like most atomizers the RDA Drip atomizer has a clean bold tasting hit. The RDA has tiny holes drilled into the side of it which provide...